EarthQuaker Devices Levitation V2

Astral Destiny™
An Octal Octave Reverberation Odyssey    
The Astral Destiny is a compact and powerful modulated octave reverb pedal that features 8 reverb modes with 8 editable presets, assignable expression control, tails for natural reverb decay when the effect is bypassed and a super cool stretch feature that doubles the length of the reverb while adding an adjustable pitch bending effect.
Tails or Full Bypass Switching
Astral Destiny can operate in two different bypass states: Tails or Full Bypass. It comes factory set in Tails Mode which allows the reverb effect to naturally decay after the effect is bypassed and is indicated by a Green Activate LED. Full Bypass will cut the reverb effect completely when the effect is bypassed and is indicated by a Red Activate LED.
Astral Destiny is buffered bypass which means that there will always be an active buffer present and it requires power to pass signal.
Stretch Footswitch
The Stretch footswitch doubles the length of the reverb effect while adding a temporary change in pitch.

• Tap for an immediate pitch change.

• Hold for a temporary pitch bending effect.

Adjusting the speed of the pitch bend
The speed of the of the pitch bending effect created by holding the Stretch footswitch can be adjusted by following these steps:

1. Hold down the Stretch footswitch.

1. Turn the Length control clockwise for a longer pitch bend or counterclockwise for a shorter pitch bend.

1. Release the Stretch footswitch once you have selected your desired length.

1. The Stretch footswitch will now operate at the selected speed every time the Astral Destiny is powered on.

Power 
This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!
Levitation™
Reverberation Machine
Have you ever wanted your tone to soar like a majestic eagle in a vast canyon? Perhaps you are a simpler mortal and just want your tone to echo like the cries of a sparrow in a small room... Now you can do both like a champ plus a whole lot more! Welcome to the Levitation™ reverberation machine! This Levitation device is a vintage-voiced reverb that aims to fit somewhere between dirty sixties chambers, classic spring and the big, ringing plate reverbs of days gone by. Four knobs and one switch control quite a bit more than you’d expect. Want a slap back small room sound? Set all of your controls to the minimum and use the mix to dial in the sound of room devoid of any thing but a guitar and amp. Want to revel in infinite spatial oscillations? Flip the toggle to Long, turn up the Atmosphere and Decay then tune out. Dial in a bright chiming slap back by turning the Tone all the way counterclockwise and reducing the Decay. Dime everything for a rattling, full-bandwidth assault. You are only limited by your imagination!
Flexi-Switch® Technology
This device features Flexi-Switch® Technology! This relay-based, true bypass switching style allows you to simultaneously use momentary and latching style switching.

• For standard latching operation, tap the footswitch once to activate the effect and then tap again to bypass.

• For momentary operation, hold the footswitch down for as long as you’d like to use the effect. Once you release the switch the effect will be bypassed.

Since the switching is relay based, it requires power to pass signal.
Power 
This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES! 

This device features Flexi-Switch® Technology! This relay-based, true bypass switching style allows you to simultaneously use momentary and latching style switching.
For standard latching operation, tap the footswitch once to activate the effect and then tap again to bypass.
For momentary operation, hold the footswitch down for as long as you’d like to use the effect. Once you release the switch the effect will be bypassed.
Since the switching is relay based, it requires power to pass signal.
This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!